Table of Contents
Why wont my kawasaki mule idle?
Mostly likely the throttle body is dirty. You can take it off and clean it, or you can run a couple tanks of gas w seafoam or injector cleaner through it.
How do you adjust the idle on a mule 3010?
Locate the idle adjust screw, or accelerator stop screw on the side of the carburetor that is above the top of the rear axle of the vehicle. Loosen the idle adjust screw by moving it a 1/4 turn, counter-clockwise. Start the engine and see if it runs smoother.
How fast does a Kawasaki Mule 3010 go?
Dual- and triple-cylinder engines, rugged styling, Kawasaki Automatic Power-Drive System (KAPS), and a high-mount air intake design are among the highlights of this rig. A 25-mph top-end speed and unremarkable aesthetics are some of its drawbacks.
How can I make my Kawasaki 4010 Mule faster?
An easy way to increase the top speed of your Kawasaki Mule is to make sure that the tires are fully inflated — the flatter your tires are, the slower you’ll go. Disabling the governor is another action you can take to reach faster speeds.
What does DFI mean on a Kawasaki mule?
August 24, 2009. By Dave Worden. In part two of this series, I am going to cover the basic theory that two engine manufacturers use in DFI/EFI. Kawasaki uses Digital Fuel Injection (DFI) and Kohler Co.
How do you adjust a Kawasaki carburetor?
Turn the adjustment screw at the front of the carburetor clockwise until the engine rpm starts to drop, and note the position. Turn the adjustment screw counterclockwise until the engine rpm picks up and then back off; note the position. Turn the adjustment screw between the two noted positions.
How fast is a Kawasaki Mule 550?
20 mph governed top speed.
How fast is a Kawasaki Mule 4010?
Powertrain: Engine, Transmission, and Performance The 617cc V-twin is now fuel injected, so power delivery is smooth and linear up to its 25 mph top speed.
Can I make my Kawasaki mule go faster?
An easy way to increase the top speed of your Kawasaki Mule is to make sure that the tires are fully inflated — the flatter your tires are, the slower you’ll go. Disabling the governor is another action you can take to reach faster speeds. At 3,600 rpm, though, you should be able to hit the vehicle’s top speed.
How many hours will a Kawasaki Mule last?
They’d typically put about 15,000 hours on a 550 before it was retired and one of them still lives just fine on a farm with almost 16,500 on it now.
Can you make a Kawasaki Mule pro Fxt faster?
REV-PRO Kawasaki Mule Pro-FXT 800 Rev Governor can be adjusted quickly and easily to reach an even or a higher rev range than the stock set in order to override stock top end limit.
What’s the idle problem on a Kawasaki MULE?
We have a 3010 Mule that will idle perfectly, but will falter when the throttle is opened. It will run up a bit and then do nothing as long as the throttle is open. It is about three years old but has low hours (42). I expected to find stale gasoline and gunk in the float bowl, fuel filter, and carbureter bowl.
How old is an OT Kawasaki 3010 mule?
It will run up a bit and then do nothing as long as the throttle is open. It is about three years old but has low hours (42). I expected to find stale gasoline and gunk in the float bowl, fuel filter, and carbureter bowl. Everything was clean, the float is OK, and the electric fuel pump has good pressure and volume.
Is the carburetor float on a Kawasaki MULE adjustable?
Might be able to improve things, raising the float a bit, but carburetor float is plastic and non-adjustable. Some people have re-jetted the carburetor and reported a big improvement, there are different size jets available from Kawasaki, seems they come from the factory with a number of different jet sizes.