Menu Close

Does the Alphabetic Index provide the full code?

Does the Alphabetic Index provide the full code?

It is important to use both the Alphabetic Index and Tabular List to code because the Alphabetic Index does not always give the full code. Referring to the Tabular List to verify that no other character is required.

Can the coder assign codes directly from the alphabetic index alternatively can the coder use only the tabular list?

GENERAL INPATIENT CODING GUIDELINES. Use both the Alphabetic Index and the Tabular List when locating and assigning a code. Reliance on only the Alphabetic Index or the Tabular List leads to errors in code assignments and less specificity in code selection.

What are the three main steps to coding accurately?

Accomplish this by doing the three-step approach in finding the condition in the alphabetic index, verifying the code and looking for the highest specificity in the tabular index, and reviewing the chapter-specific coding guidelines for any additional guidance.

What are the 8 steps to accurate coding?

Terms in this set (8)

  • Identify the main term(s) in the diaagnostic statement.
  • Locate the main term(s) in the Alphabetic Index.
  • Review any sub terms under the main term in the Index.
  • Follow any cross-reference instructions, such as “see.”
  • Verify the code(s) selected from the Index in the Tabular List.

What does see also mean in coding?

The “see” instruction following a main term or subterm refers you to an alternate entry to locate the correct code. Similarly, a “see also” instruction following a main term or subterm indicates than an additional term should be referenced to provide additional information. Instructional Notes in the Tabular List.

What is main term in coding?

For ICD-9 your main term is the condition, disease or symptom. For CPT the main term could be the condition, name of procedure or medical service, name of anatomic site or organ, OR synonyms, eponyms or abbreviations.

What are the coding guidelines for inpatient coding?

General Inpatient Coding Rules And Regulations

  • When coding, for greater accuracy, use both the alphabetic index and the tabular list to ensure that no errors are encountered.
  • Always assign all the five digit ICD codes if they are available and use four and three digit codes only when no other information is available.

Can modifier 22 be assigned 99291?

Can modifier -22 be assigned to 99291, 99292 codes? No, because a note in CPT Appendix A states modifier -22 cannot be appended to an E/M code. This modifier indicates an increased service and is overused and results in an increase in payment of 20% to 30%.

What are the 7 steps to accurate coding?

Terms in this set (7)

  • locate the diagnosis in patients health record.
  • determine main term of stated diagnosis.
  • find main term in alphabetic index.
  • read and apply any notes or instructions.
  • cross reference code found in alphabetic index.
  • read and be guided by conventions and symbols.
  • code to highest level of specificity.

What are the 7 steps in coding?

The seven steps of programming.

  • Step 1: Define the Program Objectives.
  • Step 2: Design the Program.
  • Step 3: Write the Code.
  • Step 4: Compile.
  • Step 5: Run the Program.
  • Step 6: Test and Debug the Program.
  • Step 7: Maintain and Modify the Program.

What is the code next to the main term called?

Default Codes A code listed next to a main term in the ICD-10-CM Alphabetic Index is called a default code, which: • Represents the condition most commonly associated with the main term; or • Indicates that it is the unspecified code for the condition.

Is Acute a main term in coding?

For example, in the ICD-10-CM Page 3 ICD-10-CM Official Guidelines for Coding and Reporting 2014 Alphabetic Index under the main term Enteritis, “acute” is a nonessential modifier and “chronic” is a subentry. In this case, the nonessential modifier “acute” does not apply to the subentry “chronic”.

How to get the index of a character in the alphabet?

What you do instead is : “Create an empty array. Push chars into it. Return the array”. Then it becomes : Also, as 200_success said, validating that char is a string and that it is not an array is redundant, so it can be further simplified to : The alphabet would be simpler if it were written as a string, and it should be const.

What’s the difference between tabular list and alphabetic index?

First, locate the term in the Alphabetic Index and then verify the code in the Tabular List. Instructional notations serve as guides. Likewise, people ask, what is the difference between alphabetic index and tabular list?

How do you write out an alphabet code?

Begin by writing down the alphabet in order on a piece of paper (or use the one below). Now pick a number between 1 and 25. Got it? I picked the number 3. Now, when you write down your coded message, instead of writing the real letter, you find that letter in the alphabet and count forward – as many letters as the number you picked.

How to stack exchange integer to alphabet string?

– Code Review Stack Exchange Integer to Alphabet string (“A”, “B”, …“Z”, “AA”, “AB”…) So this question is prompted by two things. I found some code in our source control doing this sort of things. So when I thought about this problem this popped into my head almost immediately.